Silver Spring

CIMCON’s Plug & Play Wireless Lighting Controller (iSLC) with Remote Monitoring, Dimming, GPS, Metering and Sensor Input Capabilities

CIMCON’s iSLC-3100-7P-S

CIMCON’s iSLC-3100-7P-S is an intelligent wireless lighting controller with exceptional fault tolerance and a multitude of features. Each iSLC-3100-7P-S provides intelligent ON/OFF switching, dimming control, GPS, highly accurate power metering, analog and digital sensor inputs and constant status and health monitoring of your lighting fixtures.


  • A Photocell in Every Controller: CIMCON’s iSLCs operate immediately upon installation without dependency on the network.

  • A GPS in Every Controller (Optional): CIMCON’s GPS capabilities reduce install times and eliminate future mapping issues. GPS coordinates for each iSLC are sent automatically to the Central Management System for overlay on a Google Maps interface. Without GPS, installers must manually record the pole ID, iSLC ID and its Latitude/Longitude location to map them correctly.

  • Extended Surge Protection: CATB surge protection is standard, while CATC surge protection is available as an option.

  • Full ANSI C136.41 7-pin Dimming Receptacle Support: CIMCON’s iSLCs work with any lamp type or manufacturer with full support for all 7-pins on the ANSI C136.41 dimming receptacle for true “plug and play” installation. CIMCON’s controllers support the addition of digital or analog sensors, such as motion, vehicle counts or environmental sensors through pins 6 and 7.

  • Revenue Grade Energy Metering: CIMCON’s iSLCs monitor Current, Voltage, Frequency, Power Factor, kW and kWh, and offer metering accuracy as high as. 5% for accurate consumption data and billing.

  • Fault Tolerance: Each CIMCON iSLC is a highly intelligent stand-alone device that utilizes the latest developments in self-organizing, self-healing, wireless technologies. Proper operation and execution of a light’s schedule is not dependent on network communications.

  • Remote Control and Scheduling: CIMCON’s iSLCs support multiple lamp control modes such as user configurable ON/OFF/DIM schedules programmed on a daily/monthly/special events basis, local ad-hoc control, photocell and astro-clock scheduling, and mixed mode scheduling incorporating sensor inputs.

  • Flexible Dimming Control: CIMCON’s iSLCs support dimming through 0-10 VDC, PVM or DALI interfaces

  • Fault Monitoring: CIMCON’s iSLCs provide extensive fault monitoring to report on day burners, burnouts, lamp cycling, ballast failures, over/under voltage, abnormal power consumption, low power factors, communication failures and more. All faults are sent to the Central Management System for alarm routing, visualization and fault correction. Alerts can be sent directly to relevant users immediately when they occur.

Controller

Powerful 32-bit Microcontroller

Power Metering

Parameters measured: Voltage, Current, Power Factor, Frequency, kW and kWh

Switching Capacity

15 A Max (1800 VA)

Power Supply

Universal AC input 85 V-264 V, 50/60 Hz (305 V optional)

Radio Communication (Silver Spring Networks)

Processor: ARM 7, RAM: 8 MB, Flash: 16 MB

NAN Network:
Date Rate: 50 to 300 kbps
Frequency Range: 902-928 MHz
Spread Spectrum: Frequency Hopping
Transmitter Output: 27-30 dBm (1W)
Receiver Sensitivity: -98 dBm for 10% PER
Protocol: IEEE 802.15.4 g
 
Security:
Addressing: IPv6
Encryption: Advanced Encryption Standard (AES-128 or AES-256)
Security: Secure Hash Algorithm 256-bit (SHA-256) and RSA-1024 or ECC-256
Key storage: Secure NVRAM with tamper detection and key erasure

GPS Module Specifications (Optional)

Receiver Type: 22 Tracking/66 Acquisition Channel GPS Receiver GPS L1, C/A Code

Max. Update rate: 10 Hz

Sensitivity:
Tracking: -165 dBm
Reacquisition: -160 dBm
Cold starts: -147 dBm
 
Time-To-First-Fix:
Cold starts: 31s (typical)
Warm starts: 30s
Hot starts: <1s
EPO Assist: 13s(CTTFF)
 
Accuracy:
Automatic Position3: 2.5m CEP
Speed: 0.1 m/s

Dimming Interface

Control Voltage: 0-10 V

Maximum Current: 10 mA

with Short Circuit protection

or

PWM Dimming: 10 V p-p, 400 Hz

Maximum Current: 10 mA (Sink)

or

DALI

Optional Sensor Inputs

Provision of one Digital input and one Analog input that can be used for motion-based lighting controls, adaptive lighting or advanced lighting controls

Surge Protection

Standard: 410 Joule CATB (6kV/3kA), Optional: 700 Joule CATC (20kV/10kA)

Operating Conditions

-40°C to +70°C / -40°F to +158°F, 20% to 90% Rh non-condensing; IP66

RoHS

Yes

Central Management System

Web-based software allows remote configuration, monitoring, control, and reporting

Certifications

UL, CUL, CE